| Prior to installing a body kit on your
| |
| | hardware.Side Skirt Installation:After
|
| car, you should take proper steps to
| |
| | removing your old side skirts, use a
|
| ensure that it is done correctly. We
| |
| | cloth to clean the using the procedure
|
| encourage you to have the parts installed
| |
| | mentioned above. Once prepped, pre-fit
|
| by a professional but for those you who
| |
| | the side skirts onto the car to make sure
|
| want to do the project on their own these
| |
| | parts are properly aligned. Use a grease
|
| directions will get you started.Prepping
| |
| | pencil to mark where you want to install
|
| & Cleaning Procedure:Using a good quality
| |
| | the side skirts. Now you will need to
|
| paper towel and grease remover or lacquer
| |
| | measure out a strip of double sided tape
|
| thinner, completely and thoroughly clean
| |
| | and attach it to the side underside of
|
| the painted surface area on the car where
| |
| | the side skirt if they did not come with
|
| you will apply double sided tape. Do not
| |
| | it. Peel back about 2" of the plastic
|
| allow the paper towel or cloth to remain
| |
| | backing from the tape, so you can
|
| on the car for too long as it will cause
| |
| | position the part on the car with the
|
| damage to the painted surface. Once
| |
| | remaining plastic backing still on the
|
| cleaned, use a minimum amount of adhesion
| |
| | tape. Position the part on the car and
|
| promoter (just enough to fully coat the
| |
| | once in place pull the plastic backing to
|
| surface) on a clean lint-free cloth and
| |
| | expose the double sided tape and press
|
| apply a thin coating to the surface where
| |
| | firmly to assure good adhesion. If screw
|
| you will apply the double face tape. All
| |
| | holes do not align properly you will need
|
| the adhesion promoter to completely dry
| |
| | to drill them yourself at this point. Use
|
| before you attempt installing the new
| |
| | a screwdriver to attach screws.Rear
|
| part(s).Note: If you do not intend to
| |
| | Bumper Installation:Remove your old
|
| paint your entire car, we highly
| |
| | factory rear bumper and trim panel that
|
| recommend that you paint the bumper prior
| |
| | is located above the bumper. Save all of
|
| to installing it on your car.Front Bumper
| |
| | the original factory hardware for later
|
| Installation:Remove your old factory
| |
| | use. You may need to discard the
|
| bumper and save all of the hardware to
| |
| | styrofoam absorber as the new bumper may
|
| use later. You may need to remove the
| |
| | not fit properly over it. Place the
|
| styrofoam insert as the new bumper may
| |
| | bumper on the car to test fit it. Once
|
| not fit properly over it. Pre-fit the new
| |
| | you have it lined up properly and fit is
|
| bumper on the car to make sure that
| |
| | assured drill holes into the new bumper
|
| everything lines up. If it does not, make
| |
| | using the original factory bumper holes
|
| adjustments by sanding or grinding. Use
| |
| | as a reference. Using the original
|
| your old factory bumper as a guide to
| |
| | factory screws, attach the bumper to your
|
| drill new holes into your new bumper.
| |
| | car. You may need to drill additional
|
| Once you have done so install the new
| |
| | holes into each wheel well to secure the
|
| bumper with the original factory bumper
| |
| | bumper.
|
